PDC
JNTUH
BITS
SECTION-I: Multiple
choice questions
1. Bootstrap’s sweep circuit
produces _____ type of waveform. [ a]
(a) positive going Ramp
(b) negative going Ramp (c) either a or b (d) Both a and b
2. The gate signal is
also called as ___________. [c ]
(a) enabling pulse (b) control pulse (c) both a and b
(d) either a or b
3. Sampling gates are
used in _______. [d]
(a)Multiplexers (b) D to
A converters (c) Sample and Hold circuits (d) All the above
4. The variations in
phase delay occur due to ____. [c ]
(a) variations in loop
gain (b) variations in supply voltage (c) both a and b (d) None
5. Among the logic
families, low power dissipation is in _____. [ b]
(a)DTL (b) CMOS (c) TTL
(d) ECL
6. Synchronization is
said to be with frequency division, if the generators operate at___ [b ]
(a) same frequency (b)
different frequency (c) both a and b (d) None
7. Synchronization with
symmetrical signals is possible if_______. [c ]
(a) Tp <= T0 (b) Tp >=
T0 (c)
both a and b (d) either a or b
8. Which of the
following logic family has highest fan-out. [ d]
(a) ECL (b) TTL (c) DTL (d) CMOS
9. Among the logic
families, Slowest logic family is_____. [c ]
(a)TTL (b)DTL (c)CMOS (d)ECL
10. In Miller circuit,
the gain A of the inverting amplifier should be ____. [c ]
(a) unity (b) zero (c) infinite (d) None of the above
11. The time during which the waveform returns to the
initial value is called: [b ]
(a) fall
time (b) flyback time (c) rise time (d) delay time
12. The circuit which require an amplifier whose gain
is nearly infinity [ b]
a) Boot strap ckt b)
Miller ckt c) Phantastron ckt d) Inductor ckt
13. When generators with equal frequencies run in synchronism,
the synchronization is said to be on a [ a]
a) one-to-one
basis b) one-to-two basis c) two-to-one basis d) one-to-four basis
14.
A Transmission circuit which allows an input Signal to pass through it during a
selected interval and blocks it passage outside this time interval is called: [
a]
a) sampling gates b) conventional gates c)
non-conventional gates d) logic gates
15. In unidirectional sampling gate the combination
of RC forms a [ b]
a)Differentiator b)
Integrator c) Coupling elements d) Multivibrator
16. The ratio of maximum deviation to the sweep
amplitude is called [ b]
a) Slope error (b)
displacement error (c) Transmission error (d) Linear error
17. A capacitor is charged linearly from a constant
current source is used to generate [c ]
a)sine wave form (b)
pulse wave form (c) time base waveform (d) trapezoidal wave form
18. The several factors which affect phase delay given
rise to [ a]
a)
Phase jitter b)amplitude jitter c)both amplitude and phase jitter d)frequency
jitter
19. The interval of time is selected by means of an
externally applied signal termed as:
[b ]
a) Transient signal b) gating signal c) output signal
d)exponential signal
20. Logic gates are the basic elements that make a [ d]
a) analog system b) gating system c)
basic system d)digital system
21.The relation between the slope
error, displacement error and transmission error is
22. To get a saw-tooth out put waveform, the restoration
time is [ a]
( a ) zero ( b ) rise time ( c ) storage time ( d )
infinity
23. In Miller time base generator, which of the
following is used [b ]
(a) an inverting amplifier with a gain of unity (b)
an inverting amplifier with a gain of infinity (c) non-inverting amplifier with
a gain of unity (d) non-inverting amplifier with a gain of infinity
24. Synchronization with symmetrical signals is possible
for [ d]
( a ) Tp = To only ( b ) Tp<To only ( c ) Tp >To only
( d ) both Tp<To and Tp> To
25. The time during which the output increases linearly is
called [ a]
( a ) sweep time ( b ) flyback time ( c ) return time ( d )
restoration time
26. The interval of time of transmission of a signal in a
sampling gate is selected by means of [ c]
( a ) time delay ( b ) off time of gate ( c ) gating signal
( d ) source signal
27. The following all are disadvantages of unidirectional
gate, except [d ]
( a ) interaction between the signal source and control
voltage source ( b ) limited used of gate ( c ) slow rise of the control
voltage ( d ) little time delay though the gate
28. Which of the following logic gives the complementary
outputs? [ d]
( a ) DTL ( b ) RTL ( c ) TTL ( d ) ECL
29. The voltage at the input of a gate which causes a
change in the state of the ouput from one logic level to the other is [c ]
( a ) cut-in voltage ( b ) cut-off voltage ( c ) threshold
voltage ( d ) peak voltage
30. The high state fan out of a gate is defined at when the
[ c]
( a ) input is at logic ‘0’ ( b ) input is at logic ‘1’
( c ) output is at logic ‘1’ ( d ) output is at logic ‘0’
SECTION-II: Fill in the blanks
1. The ratio of the difference between the input
and the output to the input at the end of the sweep time is called Transmission error
2. The
output of the time base generator is called Sweep Voltage
3. The gain of a sampling gate is defined as The ratio of the output voltage
to the input voltage during transmission
4. Ideal sampling gate is a transmission circuit in which the output
is an exact replica of input waveform during a selected time interval and is
zero otherwise.
5. The periodic
variations in the phase delay are called Phase jitter
6. The range of synchronization increases with
increasing sync signal
amplitude
7. The relation between slope error and
transmission error is es=2et
8. Typical noise margin for DTL family is 700mv
9. CML is also called
as ECL
10. In a 4-diode sampling gate, minimum value of Vc is
given by Vcmin=Vs
[2+Rc / RL]
11.The maximum number of gates that can be driven
by any logic gate is called Fan out
12) If synchronization is achieved with different
frequencies, i.e one frequency being n times the other, then it is termed synchronization with frequency
division
13) Two or more generators are said to be running synchronously if all of them arrive at some point in the
cycle at exactly the same instant of time.
14) Sampling gates
are used in chopper amplifiers
15) In positive logic system, the higher of the two voltage levels
represent logic 1 and lower logic is 0
16) A voltage time base generator is one
that provides an output voltage waveform a portion of which exhibits a linear
portion with time
17) The ratio of the difference in slope at
beginning and end of the sweep to initial value of slope is called slope error or sweep
speed error
18) Sampling gates are classified into two types
19) Chopper often called as modulator
20) A positive logic NOR gate is equivalent to
negative logic NAND gate
21).The time required by the sweep voltage to
return to the initial value is called
restoration time,
return time or flyback time
22. Compensating networks used to improve the linearity of bootstrap circuit
23. The output of a time-base generator is called sweep voltage
24. The range of synchronization decreases with decreasing of sync signal amplitude
25. When generator with equal frequencies run in
synchronism, the synchronization is said to be on a one to one
basis
26. Bidirectional sampling gates transmit signals in both
the polarities
27. The sampling gate is used in sampling scope because the
display consists of samples of input waveform
28. The power required by the gate to operated with 50%
duty cycle at a specified frequency is called power
dissipation
29. High state nose margin of a gate is defined as VOH(min)-VIH(min)
30. The basic TTL gate is NAND gate
Prepared By
G.Swathi& Ravali